This filament spool holder is designed to fit on top of the Creality K1 or K1C once the glass lid is removed.
File types: STLLicence: Personal use only
PrintablesFreeCreality Hi horizontal filament spool holder
- Creator (as listed at the source)
- StonXX
- Licence
- CXY-SLThe licence is listed by the source marketplace. SliSearch does not verify it.
- File types
- The marketplace does not list the file types.
- Pricing
- Free
- Published
- Category
- 3D Printer Parts
- Downloads
- 83
Overview
Horizontal Filament Spool Holder for Creality Hi. I had the problem that the original holder with the filament spool was too tall. Therefore, I designed a holder where the spool sits horizontally above the printer. This saves space above the printer, and the original holder is rather flimsy and tends to wobble. (Mass centralization!) Mounting it on the printer is simple; two cable ties are sufficient to attach the base. Two M5x20-M5x30 screws with nuts are needed to mount the Teflon tube holder to the base. The original coupling is reused. The spool plate is universally designed; an M8x130 threaded rod, two locknuts, and one regular nut are required for mounting. Two 608ZZ bearings, the two adapter washers, or two 8mm Igus bearings can be used in the spool plate. An M8 washer should be placed between the base and the plate. Recesses are added in the base and the spool plate. Here you can glue in 10 x 2mm magnets to slow down the filament spool and prevent it from unwinding. I glued two magnets into each of the two holes in the base and one into each of the six holes in the plate. When gluing them in, please pay attention to the polarity of the magnets; they must attract each other, otherwise it won't work. I hope this is helpful and you like this. Now English ............................................ ;-) Horizontal Filament Spool Holder for Creality Hi. I had the problem that the original holder with the filament spool was too tall. Therefore, I designed a holder where the spool sits horizontally above the printer. This saves space above the printer, and the original holder is rather flimsy and tends to wobble. (Mass centralization!) Mounting it on the printer is simple; two cable ties are sufficient to attach the base. Two M5x20-M5x30 screws with nuts are needed to mount the Teflon tube holder to the base. The original coupling is reused. The spool plate is universally designed; an M8x130 threaded rod, two locknuts, and one regular nut are required for mounting. Two 608ZZ bearings, the two adapter washers, or two 8mm Igus bearings can be used in the spool plate. An M8 washer should be placed between the base and the plate. Recesses are added in the base and the spool plate. Here you can glue in 10 x 2mm magnets to slow down the filament spool and prevent it from unwinding. I glued two magnets into each of the two holes in the base and one into each of the six holes in the plate. When gluing them in, please pay attention to the polarity of the magnets; they must attract each other, otherwise it won't work. I hope you find this useful.
Print this model with Slicience
- Download the model from the source page.
- Upload the file to Slicience and get a quote with Prinnu.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
PrintablesFree
This filament spool holder is designed to fit on top of the Creality K1 Max once the glass lid is removed.
File types: STLLicence: Personal use only
PrintablesFree
Moving the filament holder from the top position to the side will increase the stability of the printer while improving filament guidance to the extruder.
File types: STLLicence: Personal use only
PrintablesFree
Turn any normal closet into a filament rack! All parts are friction fit. This model pairs great with [Filament Tags] Making it easier to find the filament you're looking for without having to look at the side of each roll.
Licence: Attribution
Creality CloudFree
Spool holder suitable for Ender 3 and K1 series, using original Creality parts. Works with spool holes from 55mm to 75mm.
Licence: Marketplace terms
Creality CloudPaid
I wanted to mount some filament reels above my printer, partially to make material changes easier and partially for material storage.
Licence: Marketplace terms
Creality CloudFree
9/22 update - added the XL & XXL Sizes Watch out YouTube video on how we made this!
File types: F3Z STLLicence: Public domain
PrintablesFree
A simple mount with some needed dowels (files for 20-28mm Including 3/4 and 1 Inch pipes) for your 1 kg filament spools.
File types: F3D STEP STLLicence: Personal use only
PrintablesFree
⚒ No 3D printer? No time to source components? I just opened my new e-shop where you can buy physical, ready-to-use versions of my models! Designed with passion, printed and assembled with care ⚙.
File types: GCODE STLLicence: Marketplace terms
PrintablesFree
Chronologie : Pour soutenir mon travail vous pouvez me suivre sur cette page ainsi que sur Facebook : et/ou faire un don pour rembourser mes frais (Matières, équipements, logiciels, etc...) -> Français (description in English...
File types: STLLicence: Personal use only
PrintablesFree
A filament spool roller intended for the tight space of smaller cereal boxes. This design utilizes two 608rs bearings aligned at the center of the rollers, instead of the ends.
File types: 3MF STEPLicence: Attribution
PrintablesFree
The Prusa Roller is the name of a new filament unwinding tool which fits all common filament rolls. It has been designed so that the extruder has to overcome as little rolling resistance as possible.
File types: STLLicence: Personal use only
PrintablesFree
A simple storage solution for my PLA spools that I just keep at room conditions, using a 22mm dowel. It also could be used floating inside the shelf, if you got the "air space" between your cross...
File types: STLLicence: Personal use only
PrintablesFree
This design solves all the basic necessities: Fits almost every object with a flat top surface and printer frame when customized. Can easily hold the weight of 1+ kg spools.
File types: GCODE STEP STLLicence: Personal use only
PrintablesFree
Filament spool holder with 75mm, 80mm, 90mm, 100mm width. Bearing size: outer diameter: 22 mm. inner diameter: 8 mm. width: 7 mm. (I used ABEC9 roller skate bearings)
File types: STLLicence: Personal use only
ThingiverseFree
Flashforge Adventurer 5M (AD5M) Voronoi Side Mount Spool Holder. The most direct filament path there is.
File types: 3MF STLLicence: Personal use only
PrintablesFree
Eliminate the sloppy fit between your filament spools and the spool holder that came with your Creality printer.
File types: STLLicence: Personal use only
PrintablesFree
I've remixed the original STL so you don't need additional screws for the holder. Just slide it in and you're ready to go.
File types: STLLicence: Attribution
PrintablesFree
Joe3020 fitted an adapter for 10MM bearings for Overture cardboard spool, I remixed it to work on most spool holders.
File types: STLLicence: Attribution
PrintablesFree
FilaDock is a modular filament management system designed specifically for the INDX and built around the IKEA SKÅDIS medium pegboard.
File types: STLLicence: Personal use only
PrintablesFree
The adapter is tight so that there is no play and can withstand the load of the filament. The adapter is attached using the original spool holder screw.
File types: BGCODE STLLicence: Attribution
PrintablesFree
This Filament Spool Ring (Alzament) is a simple and effective solution to reduce friction inside filament spool hubs , especially for cardboard spools.
File types: 3MF BGCODE STEP STLLicence: Personal use only
PrintablesFree
5 kg Spool Holder with Adjustable Support I made this remix of creations by Uncle Jessy , rbliss , and Firstlayer Oy , to fit my newly bought 5 kg spool of SUNLU filament.
File types: 3MF STLLicence: Personal use only
PrintablesFree
Supported Printers Ender 3 V3 SE Ender 3 V3 KE x2 M4 Screws (Included with printer) x2 M3 Screws x2 M3 Heat Inserts x4 608 Bearings (2RS or ZZ) Print Settings Printer brand: Ender-3 V3 SE Doesn't...
File types: STEP STLLicence: Attribution
PrintablesFree
I don't like the original spool holder, you need two hands to slide the filament spool on and off, and spools with larger inner diameters fall off. This spool holder uses the original axle.
File types: STLLicence: Personal use only
PrintablesFree
Muscle arm spool holder for the Voron V0.2. it uses the base of the stock spool holder & includes the slot for the tube. Not modelled with supports in mind.
File types: STLLicence: Attribution
PrintablesFree
Filament Holder using 6801 bearings instead of 6801. 2-sided roller base used for the Adventurer 5m (minimal enclosure) remix included.
File types: STLLicence: Personal use only
PrintablesFree
Remix of HugoG's Filler - Filament Holder as a top-feed spool holder for an Adventurer 5m using design8studio's minimal enclosure. x2 608 bearings are needed.
File types: STLLicence: Personal use only
PrintablesFree
Simple spool hook to hang filament from any rod. We used our closet rod. We also added a longer handle to make gripping easier. This is a simple print. Set infill to 20% and supports are optional.
Licence: Personal use only
Creality CloudFree
DESCRIPTION: This is a compact airtight filament spool container designed specifically around the 220×220 build volume of the Creality K1C.
Licence: Marketplace terms
Creality CloudFree
*This model is designed to install and remove filament spools in a practical way. *Thanks to its mechanism, it rotates easily, making it easier for the 3D printer to draw the filament.
Licence: Marketplace terms
Creality CloudPaid
Adapters for the ingenious Hula feet on the Creality HI. The original HI rubber feet remain in place; the printer is simply placed inside the Hula feet. Therefore, no modifications to the printer are necessary.
Licence: Marketplace terms
Creality CloudFree
I designed this Creality Hi original spool holder modification to place the filament on the side for my enclosure. It utilizes both the original filament guide and the spool holder (along with the original PTFE tube for guidance).
Licence: Personal use only
Creality CloudFree
The Filament Spool Holder with Silica Gel Container is a practical solution designed to enhance the quality of your 3D printing experience by ensuring your filament remains dry and free from moisture-related issues.
Licence: Personal use only
Creality CloudFree
Because I had a crack at the weak point of my original spool holder rack, I created a new one. The original part is no longer for sale, so you can use the original spool holder tube.
Licence: Personal use only
Creality CloudFree
Design Concept The design aims to solve common issues with fragile filament spools prone to breaking. By utilizing the adapter, users can easily manage their filaments without interruptions or entanglements.
Licence: Marketplace terms
Creality CloudFree
Design Concept This spool adapter is designed to fit Sunlu TecBears filament spools, specifically tailored for use with the CFS/AMS system. The adapter is engineered to ensure a smooth rotation and optimal filament feeding experience.
Licence: Marketplace terms
Creality CloudFreeSliSearch lists public model details and links to the original source. It does not host files or verify licences.