Printables
I sit my cyclone separator on top of my dust collector, but it slides off sometimes when I'm using the hose to clean out my CNC. I made this tall and thick bucket holder so that even when pulling hard, the bucket won't pop out.
I affixed mine to the top of the dust collector with some silicone glue. Hot glue doesn't stick well to the glossy paint of the FoxAlien.
Chosen by shared tags first, then category. Each one links to its own marketplace.
MINI TRACK LOADER RC This is a Mini Track Loader RC like BobCat vehicle. Simple to print and simple to assemble, this Loader works with: ALL YOU NEED : - 3x "3.7g Micro Mini Servo : EU : - RX and TX EU : - Lipo 1s : EU : - some M3 screws...
File types: STLLicence: Attribution
ThingiverseFreeA small trash can will fit nicely under a desk or makeup table.
Licence: Personal use only
Creality CloudFreeThis rod holder sits over the top lip of a 5 gallon Menards bucket. The hole opening is 1.1" diameter which works with most of my rods. All buckets are different in top lip design but it may work with others.
File types: STLLicence: Personal use only
ThingiverseFreebucket was designed for 1/10 scale rc rock crawler jeep wrangler, for best results scale it to the size you need
File types: STLLicence: Attribution
ThingiverseFreeThis is a flanged adapter that I created for converting a 5 gallon bucket into your Cyclone Dust Collector
File types: STLLicence: Attribution
ThingiverseFreeThis is a hydraulic powered crane/digger/bucket thing. Not quite sure what to call it. It is powered with Syringes that slide into the holes and attach to to the syringe mounts.
File types: STLLicence: Attribution
ThingiverseFreeI designed and printed a magnetic poop bucket, which sits below the fans and has a chute to capture the excess filament that is ejected. I had to estimate the hole size in the back, based on the fan measurements.
Licence: Attribution
Creality CloudFreeRegal has turned our April's Fool social media post into an actual 3D print-at-home collectible popcorn container for Busboys! Now fans can print their own collectible popcorn container to celebrate Busboys at Regal theatres.
File types: STLLicence: Personal use only
ThingiverseFreeFile types: STLLicence: Attribution
ThingiverseFreeSmall paint container to add to hobby work. It is also water proof.
File types: STLLicence: Public domain
MakerWorldFreeHe creado este enganche similar al original del palomitero de Grogu. Engancha perfectamente sin problemas al palomitero y la figura de Grogu.
File types: 3MF STLLicence: Marketplace terms
Cults3DFreeHandle Grip for Canvas Wall Bucket This custom red handle grip is designed to reinforce and upgrade the braided rope handle on a canvas wall bucket.
File types: STEPLicence: Marketplace terms
MakerWorldFreeThis two piece designed setup routes the dust collection hose up and away from the head and connects it to a part at the rear left side of the table. It uses the existing frame holes and features to mount.
File types: STLLicence: Marketplace terms
Cults3DPaidDesign Concept The vintage bucket design captures an era's nostalgia with decorative prints depicting children celebrating a festival with colorful lanterns.
ThreedingPaidI use this for tools but it can be used for anything. Originally intended for trash.
File types: STL
This is an openscad script that generates precisely contoured gaskets for sealing bulkhead connectors or passthroughs to cylindrical or conical surfaces (such as a bucket, barrel, or tube).
File types: SCADLicence: Personal use only
ThingiverseFree*Important Note: The quadrants are NOT identical. You will need to print one of each for the center threads to work correctly.
File types: 3MFLicence: Personal use only
PrintablesFreecan be printed with no supports has bolt holes (for nut & bolt). would recommend using some sort of sealant/adhesive to seal the joint. fit on the bucket & lid, trace the cutouts and bolt holes, clear them out, fasten together.
File types: STLLicence: Personal use only
PrintablesFreeThis filter sits at the bottom of a 5-gallon bucket. Slats filter out dirt, airsoft bb's, and other debris. I designed this for when we play Nerf at the Airsoft arena and use sweepers to pick up darts.
File types: 3MFLicence: Personal use only
PrintablesFreeAlignment square utilizing the alignment pins on the Carvera (Air) to correctly align the FoxAlien low profiel vise.
File types: STEP STLLicence: Personal use only
PrintablesFreethis bucket is so you can excavate in sand/water so sand/water will fall through leaving rocks/mud inside
File types: STLLicence: Personal use only
PrintablesFreeI have two of these devices and they work great, but I needed an additional part that would allow me to collect what I cut.
File types: STLLicence: Personal use only
PrintablesFreeA hose adapter to fit the Fox Alien Dust Collector hose (31.7mm diameter) onto the Carvera Air. I added a large fillet around the hose hole, which has made it super easy to pop in/out.
File types: F3D STLLicence: Attribution
PrintablesFreeThis is the perfect set of 3D models for a day at the beach or at the park with the kids. 3D-print the set as is, or scale the items to fit your 3D printer’s build plate.
File types: STLLicence: Attribution
ThingiverseFreeIn the tradition of barrel of monkey's these guys are meant to link together en masse. They can form chains or even checkered sheets by connecting on all four corners.
File types: STLLicence: Attribution
ThingiverseFreeNeeded a sturdy little trash can, so i designed this relatively simple model with a nice pattern on the walls to make it stiffer. total size: 200x200x225mm
File types: STLLicence: Personal use only
ThingiverseFreeFor hanging on a Louvre hook panel, or simply stacking up in a pile, to sort all your nuts and bolts, bits and bobs, odds and ends in.
File types: IGS STLLicence: Personal use only
ThingiverseFreeBoost Me Just Do It ! ⚠️ LICENSE — PERSONAL USE ONLY This model is provided under the MakerWorld Standard Digital File License.
File types: 3MFLicence: Marketplace terms
MakerWorldFreeA waste container bucket for the new K2 (260x260mm) and the K2 Pro (300x300mm) printers from Creality. You can screw on the mount bracket using the original screws and then easily slide on and off the bucket for easy emptying.
Licence: Personal use only
Creality CloudFreeThis is an ergonomic handle replacement for 5 gallon buckets. I replaced the handles on a bunch of buckets around my house. The first one I replaced because the original handle had crumbled away.
File types: SCAD STLLicence: Attribution
ThingiverseFreeSliSearch lists public model details and links to the original source. It does not host files or verify licences.
Fab365
YouMagine
