Thingiverse
Tablet holder for Amazon Fire on Celestron CPC Telescope
- Creator (as listed at the source)
- 1bigpig
- Licence
- Creative Commons - AttributionStated at the source marketplace; SliSearch does not verify licences.
- File types
- STL
- Pricing
- Free
- Published
- Category
- Learning
- Likes
- 44
Overview
This is a Amazon Fire Tablet holder for a Celestron CPC telescope (or any telescope that uses 2 inch/50mm diameter tripod lets). I purchased a wifi adapter for my Celestron CPC telescope to use the Sky Portal android app to control all the functions of my Telescope instead of using the handbox. There is a 1 inch /25mm slot between the tube mount and the tablet holder. This is for a Velcro/hook and loop tape "belt" to hold the holder against the tripod leg. This prevents the tablet holder from falling off the tripod or sliding down the tube. You will need about 12 inches/ 30cm of hook and loop tape. The screen is 100% visible when in the holder, so it is not necessary to remove the tablet to use it. I added a small drain hole on the bottom of the holder. If it should accumulate dew/rain/snow/dirt, it will have somewhere to drain out--assuming the tablet is not installed in the holder. Lastly, this holder will probably work with other 7" tablets, but it was specifically designed for the Amazon Fire 7". Also, this holder will fit other telescopes with 2 inch/50mm tripod legs--ie Sky Watcher EQ-6 or Orion Atlas EQ-G mounts--just use the Sky Safari app, instead of the Sky Portal program.
Print this with Prinnu
- Download the model file from the source page. SliSearch moves no files.
- Upload the file at slicience.com/quote. Prinnu quotes it in minutes.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
Telescope Cap Holder Tripod Mount for Celestron 114 LCM
Leave-On Tripod-Spreader Lens Tray for Celestron Nexstar SE TelescopeI found it annoying that the tripod spreader (lens/accessory tray) that came with my Celestron Nexstar 8SE telescope needed to be removed to fold in the legs, and also was a little too wide to fit in some tripod carrying cases.
Tripod Clip On Box for Celestron LCM Telescopes
Duncan Mask for Celestron CPC8
Celestron Nexstar 127 STL Solar Filter ( No Glue)Celestron NexStar 127SLT Solar Filter – Easy-to-Print 3D Model This is a 3D printable solar filter housing designed specifically for the Celestron NexStar 127SLT telescope.
Phone holder for TelescopeThis is a universal phone holder for the telescope. The holder is designed to be strong, durable, easy to print and without the use of any additional material, supports or glue 0.2 mm layer / 0.4 mm...
Tri-Bahtinov mask for Celestron C11 telescopeTri-Bahtinov masks help to achieve a very precise collimation and focus on telescopes. I have designed this mask to fit on Celestron C11 SCTs. Two version for the new chinese made celectrons and for the older ones are available.
Slow motion control knob for 6 mm shaftSlow motion controle knob with a 6 mm shaft and a heat insert. I wanted a long beefy knob with good grip. I use this on my Vixen SP DX mount. There are different versions. Choose what you need.
Celestron Nexstar Evolution Hand controller mount REMIXRemixed the original file by Spuddy at MakerWorld to reduce the wall height on the left side, so you can still easily grip the mount handle without crippling your hand.
Dust cap for Celestron C6 with HyperstarThis is intended to be printed "nose down" to get the rim to print cleanly. No supports. PETG recommended. My physical prints measured a millimeter or two smaller than the digital model was specifying.SliSearch is an index: it stores public metadata only, does not host files, does not verify licences, and has no partnership or affiliation with the indexed marketplaces.