Printables
[Use M3 screws] Spool holder for Prusa MINI Flexible
Necessary commercial parts 4 stainless steel “608” bearings. These are the same as the spooler bearings that come with the Prusa MINI.
![[Use M3 screws] Spool holder for Prusa MINI Flexible, a preview image from Printables](/previews/printables/62910/detail-263b3048d358bf3c.webp)
![[Use M3 screws] Spool holder for Prusa MINI Flexible, a preview image from Printables](/previews/printables/62910-1/detail-355db639853581c6.webp)
- Creator (as listed at the source)
- Madaco
- Licence
- Creative Commons — Attribution — Noncommercial — Share AlikeStated at the source marketplace; SliSearch does not verify licences.
- File types
- GCODE STL
- Pricing
- Free
- Published
- Category
- Accessories
- Likes
- 3,905
- Downloads
- 11,985
Overview
Necessary commercial parts
4 stainless steel “608” bearings.
These are the same as the spooler bearings that come with the Prusa MINI.
8 cap screws (M3-15 or M3-16)
Read the full description
8 nuts (M3)
Foam rubber sheet with adhesive on one side.
Recommended thickness: 2mm to 4mm.
Prepare four pieces cut to 16mmx14mm.
Affix these to the bottom of the spooler.
Notes on assembly
Each bearing holder has a specific mounting point. Please check the imprint on the printout.
Make sure that the C-ring is inserted in the correct direction. (Please refer to the attached figure.)
When inserting or disassembling the C-ring, be careful not to injure yourself as it may pop vigorously.
Install all bearings first, and then join the left and right frames together.
No rafts and supports are required for this printing.
！Note！
If you do not apply a non-slip foam rubber sheet, the screw knob will not work as expected! !
If rubber sheeting is not available, attach a small board to the bottom of the frame to give it extra bulk.
*Important Notice
Some users have reported that the screws are difficult to insert.
This may be due to individual differences in the 3DP. For this reason, we have prepared a screw with a larger clearance as an option.
Normally, please print " Screw_knob_Flex_0.2mm_PETG_MINI_1h47m " for the screw. If you have trouble getting it in, try " Screw_knob_Flex(clearance)_0.2mm_PETG_MINI_1h49m ".
Print settings
Since the threaded part is delicate, please print with "0.2mm quality".
The filling rate should be at least 30%.
Use PETG or PLA filament. PETG is recommended in areas with high temperatures.
The recommended infill setting is gyroid or rectilinear.
The screw knob must be printed independently. This is because when printing with other parts, the screw part may be slightly disturbed.
When freshly printed, the screw may get a little stuck. Therefore, it is recommended to run the screw back and forth several times.
Print this with Prinnu
- Download the model file from the source page. SliSearch moves no files.
- Upload the file at slicience.com/quote. Prinnu quotes it in minutes.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
Flexible filament clipMaybe a slightly different filament Clip. First insert the clip into the spool by turning it slightly and then click the filament into the groove. Suitable for Prusament spools , or spools with an internal dimension of 60mm .
Modular Filament Storage System - ExtendedA Remix of Modular Filament Storage System that contains extended models! Extension nubs allowing for multiple rows without screws are a part of the updated wall mount brackets.
spool holderan adjustable and easy to print honeycomb spool holder
Spool Holder Elegoo Neptune 4Prints great with 2.mm layer height and 3 perimeters
SpoolHolder for 4 SpoolsThis Spool holder was one of my first tests and creation by learning CAD in Fusion360. It is not perfect but good enough for a first try.
CREALITY SPOOL HOLDERSpool holder suitable for Ender 3 and K1 series, using original Creality parts. Works with spool holes from 55mm to 75mm.
Compact Filament Reel Holder - Wall MountedI wanted to mount some filament reels above my printer, partially to make material changes easier and partially for material storage.
Creality Hi Spool HolderBecause I had a crack at the weak point of my original spool holder rack, I created a new one. The original part is no longer for sale, so you can use the original spool holder tube.
FilaDock – Modular Filament Hub for INDX & IKEA SKÅDISFilaDock is a modular filament management system designed specifically for the INDX and built around the IKEA SKÅDIS medium pegboard.
Creality K2 Spool HolderThis is only compatible with the base model Creality K2 (with 260 mm^3 print volume). The K2 has a different mechanical side profile from the K2Plus and K2Pro variants.SliSearch is an index: it stores public metadata only, does not host files, does not verify licences, and has no partnership or affiliation with the indexed marketplaces.