Printables
Base Brackets for Wismesh Repeater Mini
I recently acquired a WisMesh Repeater Mini for use in Meshtastic. The vendor also offered adjustable pole mounts, but these were unsatisfactory: they were designed for larger diameter poles, were only as stable as the adjustments locking...
- Creator (as listed at the source)
- aredington
- Licence
- Creative Commons — Attribution — Share AlikeStated at the source marketplace; SliSearch does not verify licences.
- File types
- F3D STL
- Pricing
- Free
- Published
- Category
- Electronics
- Likes
- 2
- Downloads
- 12
Overview
I recently acquired a WisMesh Repeater Mini for use in Meshtastic.
The vendor also offered adjustable pole mounts, but these were unsatisfactory: they were designed for larger diameter poles, were only as stable as the adjustments locking mechanisms, and were not in stock. I have CAD, a 3d printer, and more patience than sense.
This bracket is designed to mount to a 44mm diameter pole and I have uploaded a model for each 5-degree position between 25 degrees and 60 degrees. The model is designed to be hose clamped to the pole with a 14mm wide hose clamp.
While I included a bunch of options that should span the range of where most people on the planet live outside the tropics, there's a lot of dimensional space here. I have also included the source model created in Fusion, which is fully parametric. You can probably download the F3d and plug in your parameters for optimum sun angle, pipe diameter, and hose clamp width and get out a model that should work for your application. I've usually had good luck with adjusting parameters but fusion's wacky so YMMV.
Read the full description
The geometry of this design cannot be adapted for near tropical latitudes.
I have printed this in ASA and used it without substantial creep.
Print this with Prinnu
- Download the model file from the source page. SliSearch moves no files.
- Upload the file at slicience.com/quote. Prinnu quotes it in minutes.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
Meshtastic Antenna BracketThis is an antenna mount I designed to fit on a solar panel with a built in battery for an all in one meshtastic node.
LoRa Cavity Filter Mounting BracketLoRa Cavity Filter Mounting Bracket Compatible with BandGuard and LoRathrogar Filtar style cavity notch filters.
Adjustable Angle Bracket for Flexible Antennas | Verstellbarer Winkelhalter für Flexible AntennenThe lower part of the bracket has come loose, so I have created and uploaded a version secured with a M3x12 screw. The old lower part, which is slotted into place, is still available.
Parametric mast mount for MeshCore enclosure – FreeCADParametric mast mount bracket for IP67 boxes, MeshCore/Meshtastic nodes, and outdoor electronic enclosures.
Fiberglass antenna supportMade this support for my Meshcore repeater when i upgraded to full N =type hardware. It prevents the ariel being able to twist.
Smart Stand - A smart little stand for Smart Devices (Phones and Tablets)
Headphone stand for a desk or shelfHi this is a Head phone mount that can slip on to a shelf or on to a desk. These are design to just slip on to a shelf or desk with no effort and hold themselves in place using the materials properties to allow it to act as the spring...
Shelf Bracket - Topology Optimization
HDD Adapter 3.2I was looking for an adapter to put my 2.5" SSD drive in a 3.5" HDD bay, and found several nice designs, but none that could be screwed in from underneath, so I made one with all modern holes.
2.5 Inch HDD StandHere's the 2.5 Inch HDD stand in 6 or 8 drive options. There's honeycomb vents on the sides to keep temperatures down and to minimise print material while still maintaining good strength.SliSearch is an index: it stores public metadata only, does not host files, does not verify licences, and has no partnership or affiliation with the indexed marketplaces.