Printables
Lee Challenger Right-Side Case Kicker v1
- Creator (as listed at the source)
- phacious
- Licence
- Creative Commons — Attribution — Noncommercial — Share AlikeStated at the source marketplace; SliSearch does not verify licences.
- File types
- STL
- Pricing
- Free
- Published
- Category
- Other Ideas
- Likes
- 8
- Downloads
- 23
Overview
Case Kicker that ejects to the right, and kicks at the end of travel to allow for longer cartridges. Interacts with the Press handlebar, so the handlebar must be completely vertical when in the up position. Decapping Primer ramp included, as the Lee primer arm will cause the case to bind.
Case kickers speed up the process and quality of life for the reloader. My setup requires case access from the right, all the other kickers load/eject to the left. Figured others could use this too.
Two versions included. 3mm screw and #6 screw.
Hardware needed:
Zip Ties
Rubber band
M3x+20mm screw or #6 x +3/4" screw.
Instructions:
Screw the kicker, mount, and foot together. Ziptie the mount to the left side of the press' front column. Loop rubber band around front notch on kicker, then feed the rubberband around the front of the column and around it to the back, feed UNDER the kicker and attach to the rear peg of the mount. See pictures.
Print settings:
Filament: PLA/PETG/ASA/PA
3 perimeters
30% infill
Troubleshooting: If the kicker binds on the ram, slide the mount higher up the column.
Print this with Prinnu
- Download the model file from the source page. SliSearch moves no files.
- Upload the file at slicience.com/quote. Prinnu quotes it in minutes.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
Short Action Customs Nexus Die Lock RingThis lock ring is designed to hold any 7/8" threaded sizing or seating die in a Short Action Customs Nexus Press.
Primer Flipping TrayReloading primer flip/flipping trays. The flip tray comes in three sizes: 50, 100 and 125mm (2", 4" and 5").
Wrench for reloading dies and nutsPrecision reloading requires absolute setup repeatability, but die lock rings and lock nuts often loosen or bind when using standard metal tools.
45 acp case feeder for Dillon XL650Just realized the piece that holds the tube is bigger than the original, I have an adapter for my use, so plan accordlingly! Remixed from wanousoubi for 45 acp.
Bass Shell Casing Washing Rack for Ultrasonic BathThis is a washing rack for brass shell casings. It holds them vertically and off the bottom while using an ultrasonic bath. I designed this to fit in my 6-liter Ultrasonic bath.
Ultrasonic Wash Tray - Case RackA modular ultrasonic wash rack for 9mm and .45 ACP pistol brass casings. It keeps the cases upright so that there are no air pockets. It is recommended that you decap the brass before washing it.
Lee Six Pack Pro Reloading Press - Primer Detection AdapterA simple adapter that allows you to add a M12 metal detector to detect a failure in the primer feed ramp.
Pegboard Mount for Hornady Lock'N'Load Bullet TubesI designed this to fit my Hornady 9mm bullet tubes. I'm not sure if the .40 or .45 bullet tubes are the same diameter. Mount on 1"-spacing pegboard using my Lockable Pegboard Rivet . Holds three bullet tubes.
Hornady-Style Bullet Comparator Insert Set | Precision Measurement ToolsAchieving consistent seating depth and measuring from the bullet ogive rather than the tip is essential for long-range precision. This 3D-printable set of comparator inserts is designed to work with standard Lock-N-Load style bodies.
Pegboard mount for 8mm Primer TubesI designed this to fit my Hornady primer pickup tubes (small or large). It also holds the primer feed tubes from the Lock'N'Load AP press. The Hornady tubes are all 8mm diameter.
RCBS Brush Handle GridfinityThis is a 5x1x3 bin for holding an RCBS Accessory Handle 2, or RCBS brush handle. It is meant to hold the handle with either the nylon brush attached, or with the primer pocket brush attached.
Lyman Die Wrench GridfinityThis is a 5x2x3 Gridfinity bin for a Lyman BrassSmith Die Wrench. It is deep enough to hold 3 wrenches stacked on top of each other.
Dillon RF100 Primer Filler Small Primer chute adapterThis part replaces the small primer chute at the end of the ramp. It is offset to allow a smoother transition into the hole and doesn't flip primers.
Forster Case Trimmer Accessory Organizer | Collet & Pilot StandOverview Keeping your reloading bench organized is essential for both efficiency and precision. This 3D-printable accessory stand is designed as a direct, modern alternative to the traditional Forster Accessory Case.
Lee Classic Turret Press Brass KickerBrass Kicker for the Lee Classic 4 Hole Turret Reloading Press. Snaps in between the right two posts, easiest to install from ram side with ram at bottom of stroke.
Lee Case Trimmer | Ergonomic Handle & Drill AdapterThe Lee Case Trimmer is a classic, effective tool, but managing the brass shavings and maintaining a steady grip during high-volume sessions can be a challenge.
Hornady Comparator & Headspace Kit Organizer | Precision Measuring StandMeasuring bullet seating depth and cartridge headspace requires absolute precision, but keeping track of all the small Hornady Lock-N-Load inserts can be frustrating.
DIY Low Powder & Low Primers Sensor with Buzzer for Lee Precision presses🎯 LOW PRIMERS & LOW POWDER SENSOR WITH BUZZER DIY Safety Alarm System for Lee Precision Reloading Presses Never risk running out of primers or creating a squib load due to an empty powder hopper again!
Case kicker for Lee Value Turret PressCase kicker / shell ejector for Lee Value Turret Press. Remixed from an ejector for the classic turret press. As shown on the picture you don't need a pass-through shellholder, the kicker leaves enough space for you to insert new brass.
Vortex Powder Funnel & Reloading Trays – .378″ & .473″ Case Head (.308 Win, 6.5 Creedmoor, 223. Rem., etc)Vortex Powder Funnel – .378″ (9.6 mm) & .473″ (12.01 mm) Case Head A 3D-printable vortex powder funnel designed for fast and smooth powder transfer when reloading rifle cartridges.
7/8" Reloading Die Nut Finger Wrench
Rock Chucker Supreme Primer CatcherRock Chucker Primer Catcher – A simple, clean solution for catching spent primers. Fits standard soda bottles, making collection and disposal quick and hassle-free
Auto brassmarker for 9mm cartridgesFully automated cartridge marker for 9x19mm Luger cartridges. It can be mounted directly onto a Dillon XL750 using an adapter stand but can also be used universally.
12 gauge 45 cal sabot3D design study featuring a 12-gauge sabot and overshot-card concept. Intended for CAD visualization, fit studies, and non-live-ammunition prototyping only. I have used it with good succuss. This is an experimental, non-certified design.
12 gauge reloading pressExperimental CAD models exploring 6-point and 8-point star crimp geometries for a 2¾-inch 12-gauge shell. These models are intended for design visualization and non-live-ammunition prototyping only. I have used it with good succuss.
Buckshot WadA 3D design study of a shotgun wad geometry intended for visualization and prototyping. This is an experimental, non-certified model and is not represented as safe or suitable for use with live ammunition.
Lee Inline Bullet Feeder Sturdy Mount (45 ACP)The tube base holder has a 3mm heat insert in the middle for indexing of the tube holder itself. I used a 3mm x 12mm socket screw, the countersunk type not the socket head type.
RCBS Chargemaster Lite Spill TrayThis tray used to collect powder that bounces off during dispensing. Printed with PLA White so easy to see spilled powder, Shout out to missingno for the spill tray designed for the RCBS Chargemaster Supreme and the customizable Scad...
Powder Check for Lee Reloading PressThis is a work in progress, but it should work; this goes up to 308. You will need two retention style springs. And a QD bushing. This is to tell you that the powder has been charged, not how much.
Primer slide Lee Six Pack ProPosuvník zápalek pro přebíjecí lis Lee Six Pack Pro, čelist která drží vodítko zápalek je mírně užší, je to tak schválně, tak s tím počítejte.
9mm Ammunition Storage CaseAs of 11/6/24 the lids have been edited to open up the tolerance between the lid and case, let me know if it helps. The two print files, “9mm lid" and “9mm case" Will ONLY fit rounds that are at or less than 1.1 inches.
223 rem Ammo boxthis is for 50 .223 remington rounds and may work with other calibers. these boxes are cheap and easy to get in USA but not so much in some other countries, so you can print it.
Stackable 9mm Ammo Box 100 RoundsSturdy, Stackable, Sexy. Now we can really be an "Organized" Militia. If you've ever bought 9mm in bulk, you know that they just pile the rounds in an ammo can. It's gross. Print this and live your best life.
.270, .223, 5.56 Reloading Tray
Primer Flipping TraysIMPORTANT: Get the latest updates for this model here on PrusaPrinters. In 2021, all updates and uploads of new models were moved to PrusaPrinters, of course still free and under the same conditions...
Reloading Primer Tray Storage Dispenser
Case feederNEW MODEL AVAILABLE!!! Sorry, this first generation more is no more available and i do not have files available as originals have been lost.
Stackable .223/5.56 Ammo BoxAnother take on .223/5.56 ammo box. This one has a sliding top and is stackable.
Bullet pullerDISCLAIMER: reloading cartridges is a dangerous endeavour. All reloading and firing of reloaded ammunition is done at your own risk. Do not attempt to reload until you have read and understood at least one printed reloading manual.
Loading Sign / ThrobberReally like the symbol loading, so I made one as a hair clip. I designed different heights for multi-color printing, so that the colors can be printed on the top layer efficiently and eliminate excessive color changes.SliSearch is an index: it stores public metadata only, does not host files, does not verify licences, and has no partnership or affiliation with the indexed marketplaces.