Printables
Fully Printed 1:28 RC Car Chassis (MINI-Z compatible)
For the most up-to-date parts, visit the GitHub project page . This is a 1/28 scale RC chassis designed to be compatible with Kyosho MINI-Z body shells. Current version fits 90mm (M) wheelbase shells.
- Creator (as listed at the source)
- AlexY
- Licence
- GNU General Public License v2.0Stated at the source marketplace; SliSearch does not verify licences.
- File types
- STL
- Pricing
- Free
- Published
- Category
- RC & Robotics
- Likes
- 705
- Downloads
- 3,012
Overview
For the most up-to-date parts, visit the GitHub project page .
Video:
This is a 1/28 scale RC chassis designed to be compatible with Kyosho MINI-Z body shells. Current version fits 90mm (M) wheelbase shells.
Update 8/26/20: I've released a 4WD chassis, available here . The 4WD version is optimized for drifting, while this one is better for grip racing and is cheaper to build.
Read the full description
Features:
Independent front suspension and hinged rear suspension
Ackermann steering geometry with 45 degree max steering angle
Uses common and cheap parts (625 bearings, M3 hardware)
Low part count and variety - only 3 different screw lengths needed; locknuts everywhere
Parts List
| Part | Quantity | Notes | | --- | --- | --- | | M3x20mm button head screw | 7 | | | M3x14mm button head screw | 2 | | | M3x10mm button head screw | 8 | | | M3 lock nut | 17 | | | 625 bearing | 4 | | | 130 size brushed motor, 2s compatible | 1 | | | SG90 micro servo | 1 | | | Compression spring, ~4mm OD, ~6mm length | 2 | For front suspension. Softer springs are better. Retractable pen springs cut to ~6mm can work, but are a bit stiff. | | Compression spring, ~4mm OD, ~20mm length | 2 | For rear suspension. Uncut retractable pen springs work for this. | | Venom Fly 300mah 2s battery (JST connector) | 1 | Batteries up to 45x23x16mm should fit | | Small brushed ESC, 2S compatible | 1 | | Small radio receiver | 1 | 2 channels or more, smaller than approx 34x22x13mm. Flysky GR3E works if decased. |
Print Settings
Printer:
FuseBox2R
Rafts: No
Supports:
No
Resolution: 0.1-0.15mm
Infill:
25-30%
Notes:
Print tray1.stl at 0.15mm and tray2.stl at 0.1mm layer heights. Make sure your printer has good layer adhesion, as some parts have a small bed contact area and can warp or detach easily.
Support should not be used for any of the parts. The front wheels have a cylindrical piece of built-in support on the inside of the wheel. To remove, use pliers to grip the support and pull straight out without twisting. For more powerful motors, it may be necessary to print the motor mount and motor pinion in ABS or PETG.
Category: R/C Vehicles
Print this with Prinnu
- Download the model file from the source page. SliSearch moves no files.
- Upload the file at slicience.com/quote. Prinnu quotes it in minutes.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
Chassis 1/10 Adaptable - DKS-BasicA" parts for small servo B" parts for big servo Improvements on the following parts: Body L and R, Case Holders, Gear 1 and Rear Frame R.
Fully Printed 1:28 RC Car Chassis (MINI-Z compatible)For the most up-to-date parts, visit the GitHub project page. Video: This is a 1/28 scale RC chassis designed to be compatible with Kyosho MINI-Z body shells. Current version fits 90mm (M) wheelbase shells.
MakerZ – Open Source 1/28 RC Drift Chassis by Fails & Makes | Açık Kaynak 1/28 RC Drift ŞasisiMakerZ – Open Source 1/28 RC Drift Chassis MakerZ is a fully 3D printable 1/28 scale RC drift chassis designed for makers, tuners and RC enthusiasts. The platform was developed with a strong focus on:
VW Beetle BAJA BUG - 1/18 RC body (PXtoys 9302E)**All my designs are free to download, VW Beetle BUG - 1/18 RC body I bought a cheap RC car and designed a new body for it. You can find link to the RC car HERE .
RC Wall MountWallmount for 1:10 RC Cars. Fits Tamiya TT01 or TT02 for example. Printed mine in PLA and did the inlay out of TPU
RC 1/10 MCLAREN MCL38 RTRopenRC Mclaren MCL38 f1 car i made infill is 100% and supports are needed traxxas 2075 servo traxxas tqi remote and receiver any 3000kv motor or a 550 motor, and 60-80amp esc 2s lipo for drones decals ill figure out how to make it on a...
The Gamma - Printed in Place RC Car - version 1.8
Mini-z MR03 stand for stock chassis
1:28 Scale 2010 Hennessey Venom GT Widebody Body w/ Dummy Chassis (Xmod and MiniZ)Listed is an 10 Venom GT that fits 102mm Wide MiniZ LM chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 2010 Hennessey Venom GT Body w/ Dummy Chassis (Xmod and MiniZ)Listed is an 10 Venom GT that fits 102mm Wide MiniZ LM chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 1969 Ford Mustang RTR-X Body w/ Dummy Chassis (Xmod and MiniZ)Listed is a 69 RTR-X that fits 98mm Wide Xmods and SOME MiniZ chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 1969 Ford Mustang Boss 429 Body w/ Dummy Chassis (Xmod and MiniZ)Listed is a 69 Mustang that fits 98mm Narrow Xmods and SOME MiniZ chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 1964 Austin Mini Cooper S Body w/ Dummy Chassis (Xmod and MiniZ)Listed is a 64 Cooper S that fits 90mm Narrow Xmods and SOME MiniZ chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 1969 Ford Mustang Boss 302 Body w/ Dummy Chassis (Xmod and MiniZ)Listed is an 69 Mustang that fits 98mm Narrow Xmods and SOME MiniZ chassis using my current clip mounts (Roughly 1:28 Scale).
1:28 Scale 1964 Austin Mini Cooper Monte Carlo Body w/ Dummy Chassis (Xmod and MiniZ)Listed is a 64 Cooper that fits 90mm Narrow Xmods and SOME MiniZ chassis using my current clip mounts (Roughly 1:28 Scale).
Mitsubishi Attrage 2013 Printable Car In Separate PartsNOTE :_ You can message me via Mail, after you buy whatever scale you want we will give you Scale :-1/10, 1/24 Body Repaired:- The "Body Repaired" version is intended for you to cut the body into different parts.
Mercedes Benz GLS 2024 Printable Car BodyNOTE :_ You can message me via Mail, after you buy whatever scale you want we will give you Scale :-1/10, 1/24 Body Repaired:- The "Body Repaired" version is intended for you to cut the body into different parts.
Mercedes Benz GLS 2024 Printable Car In Separate PartsNOTE :_ You can message me via Mail, after you buy whatever scale you want we will give you Scale :-1/10, 1/24 Body Repaired:- The "Body Repaired" version is intended for you to cut the body into different parts.
Mitsubishi Attrage 2013 Printable Car BodyNOTE :_ You can message me via Mail, after you buy whatever scale you want we will give you Scale :-1/10, 1/24 Body Repaired:- The "Body Repaired" version is intended for you to cut the body into different parts.
Chasis 1/10 Adaptable - DKS-Basic12/2021 "A" parts for small servo "B" parts for big servo 03/2024 Improvements on the following parts: Body L and R, Case Holders, Gear 1 and Rear Frame R.
Mini car
BMW E46 M3 Keychain MinicarKeychain car BMW E46 M3
Digger (Loader)Block 8418 Extremely Small Scale Excavator Contains 66 pieces and two models can be built from the same pieces. Everything except the tires was printed using Eryone 1.75 PLA.
Mini Rally CarIt is a rally car mini, 2,3cm large, that is based on the mythical Subaru Impreza. This is a print-in-place model that does not need supports, and the wheels works properly. I hope that you like it!
Hot Wheels 4-Tier Angled DisplayMy stepdad asked me to print a display for his Hot Wheels collection. The first rendition was the original file that I remixed, and we then made a few changes according to his needs and available space.
Mercedes Benz 190E
Body Support Bars - PROTO36 RC Car ChassisLexan body supports for the PROTO36 RC Car Chassis. + Mod information + General information + Demostration video
RC Car Drift Wheel Slip On (Slide on)These are RC drift wheels that simply slide on over your existing wheels. They are 76 mm inner diameter (roughly 3 inches). There is a version with internal ridge and one without (plain).
Flying and Ground Mini Car: Draft: Edges of MiniFlying and Ground Mini Car In Tinkercad. Ratio: 1/10
Mini Car Spoiler Vol.10Easy to print mini Car spoiler inspirated by Spoiler from Need For Speed Underground II model LYNX Need more horsepowers this is the solution. Print instruciton: Material : anything you have Liking the content?
Mini E Revo Front BumperTraxxas 1/16 E-Revo VXL Front Bumper Custom front bumper designed for the Traxxas 1/16 E-Revo VXL . Designed to fit the 1/16 E-Revo VXL 14 mm mounting-hole spacing Clean one-piece design Strong and...
Honda civic tankThe Honda civic is a pretty small neat car theres no way you could put tank treads on it…….. Thats right after the success of the cybertank I decided to do it to a Honda Civic and see how it does, Enjoy!
Nissan GTR r34This detailed model of the iconic Nissan Skyline GT‑R R34 has been recreated with a realistic 3D‑printed texture , simulating the layered look of a printed prototype.
1:28 Scale LiPo Charging Cable Stay for Mini Z RCBoost Me Thanks in advance! Worried about plugging the wrong connection every time you charge your LiPo battery? Only to find out when the battery start sizzling or a unresponsive ESC?
Ford Mustang Mini Carhey everyone today I present to you this small Ford mustang mini car as a quick and cool print with plenty of detail packed into a mini size.
Cales de réglage de suspension RCBoost Me 🙌 Merci de visiter mon univers de création ! Chaque boost que tu m’envoies est bien plus qu’un simple clic : c’est un vrai coup de projecteur sur mon travail, et une source de motivation énorme pour continuer à créer des lampes...
Flying and Ground Mini CarFlying and Ground Mini Car In Tinkercad. Ratio: 1/10
Mini Cooper logo key holderMade a key holder for my new Mini Cooper S F55 car key. Started out with the MINI logo but made a smaller one without the “wings” on the logo as well. Will probably fit all 2nd / 3rd generation keys.
Slash 4x4 to LCG SPEED CHASSIS 100+MPHThis is my alt account of The_autistic_mechanic
Dual Mode Windup Car Open ChassisRolling chassis version of this thing I designed this before the windup car and as such it utilizes the same gear train, wheels and other components.SliSearch is an index: it stores public metadata only, does not host files, does not verify licences, and has no partnership or affiliation with the indexed marketplaces.