Test cube for new filaments. It's designed to print fast, use only a small amount of filament and give you a good first impression of what you can expect your finished prints to look like.
File types: STLLicence: Attribution
ThingiverseFreeM3D stress test
Unofficial Matter3D Printer Stress Test Cube Think your printer is dialed in? Let’s find out. This unofficial Matter3D stress-test cube is designed to push an FDM printer through a concentrated mix of challenging geometry.
- Creator (as listed at the source)
- Carson Design & Prototyping
- Licence
- Creative Commons — Attribution — Noncommercial — Share AlikeThe licence is listed by the source marketplace. SliSearch does not verify it.
- File types
- STL
- Pricing
- Free
- Published
- Category
- Test Models
- Downloads
- 2
Overview
Unofficial Matter3D Printer Stress Test Cube
Think your printer is dialed in? Let’s find out.
This unofficial Matter3D stress-test cube is designed to push an FDM printer through a concentrated mix of challenging geometry. Expect overhangs, bridges, narrow openings, sharp transitions, fine details, corners, and large surfaces—all packed into one compact print.
It’s useful for testing:
Read the full description
Cooling and overhang performance
Bridging
Retraction and stringing
Dimensional accuracy
Corner quality and ringing
Layer consistency
Top-surface finish
Overall filament and profile tuning
Print it with your usual profile first and see where your setup struggles. Then adjust one setting at a time and print it again—the cube makes a fun benchmark for comparing printers, materials, speeds, temperatures, and cooling profiles.
Printing recommendations
Print in the supplied orientation
No supports—the unsupported features are part of the test
Use your normal layer height and baseline material profile
Avoid slowing everything down on the first attempt
Record your filament, temperature, speed, layer height, and printer so results can be compared
For the full challenge, print it exactly as you would any normal model. No special treatment!
Share your results
Post a Make and include your printer, filament, settings, and the areas that gave your machine the most trouble. Clean successes and spectacular failures are equally welcome.
This is an unofficial, fan-made stress test and is not an official Matter3D product or endorsement. Matter3D is referenced with friendly appreciation—and yes, this cube can be mean to a printer.
Print this model with Slicience
- Download the model from the source page.
- Upload the file to Slicience and get a quote with Prinnu.
Similar models
Chosen by shared tags first, then category. Each one links to its own marketplace.
ThingiverseFree
This is a simple calibration object designed to test accuracy of your x, y and z axis linear travel, angular alignment and slicing settings, with some small bridges thrown in.
File types: STLLicence: Attribution
ThingiverseFree
This is a small solid cube with a spherical void inside it. This is useful to find good settings to obtain a truly transparent print on FDM printers before trying something larger and more advanced like cymon's skull dice.
File types: STLLicence: Public domain
ThingiverseFree
Test cube for new filaments. It's designed to print fast, use only a small amount of filament and give you a good first impression of what you can expect your finished prints to look like.
Licence: Personal use only
Creality CloudFree
Thank you for printing this sample card with our CR-3D high-performance filament Here are a few features of this part: - Size: 68x40x5mm - 10mm and 5mm Holes - 45° overhang test - a small bridging test - different transparency tests (0,4mm...
File types: STLLicence: Personal use only
ThingiverseFree
This is my 20mm calibration box with raised lettering showing which axis is which. I made this after printing the standard 20 mm box and forgetting how it was oriented after I had removed it from the...
File types: STLLicence: Personal use only
ThingiverseFree
just a little calibration/test cube - one 25mm size - one 30mm size - X & Y labels - do not eat ! :) - fixed the cube size , now there is a 25mm & 30mm cube. - Bangood - 3D Printer & Supplies
File types: STLLicence: Personal use only
ThingiverseFree
October 20th 2017: New Version available with bridge - October 28th 2016: Updated with the 20mm Version for easier print with bigger nozzle diameter This is my customized calibration model.
File types: STLLicence: Attribution
ThingiverseFree
The MK Cube is used to calibrate a couple of things: *Two raised sides with X and Y. *Two blank sides so we can see how overhangs look in different situations. *Raised features on the bottom to see how they look on the build plate.
Licence: Personal use only
Creality CloudFree
I visited a shop recently where they had printed models to sample the colours and texture of filaments they were selling. I loved the idea of seeing the colour and feeling the texture of the filament.
Licence: Personal use only
Creality CloudFree
Can your printer handle this? Based on the Makers Muse Lattice Cubes, this design is a similar thing in the sense that it is a lattice cube on a base.
Licence: Personal use only
Creality CloudFree
Test Print Torture Calibration Cube Printer Tuning Whenever I get a new filament, new printer or change the nozzle I will always do a Benchy or test cube to fine tune it.
Licence: Personal use only
Creality CloudFree
This is a 2 cm by 2 cm by 2 cm cube for calibrating your 3D printer. Print it, then check that all angles of the cube are exactly 90 degrees, the side are exactly 2cm long, the holes are exactly 1 mm, 2 mm and 3 mm wide on all sides and...
File types: STLLicence: Attribution
ThingiverseFree
this object tests for print angle 60-30 deg, rounds, posts, points, as well as a 10mm cube on a 20x20x1 mm square.
File types: STLLicence: Attribution
ThingiverseFree
This is a simple little 1 inch test cube that I designed to test out different filaments. It has a different sized hole going through each plane so you can learn how your printer skews dimensions based on the axis.
File types: SLDPRT STLLicence: Attribution
ThingiverseFree
just testing rotating sphere in Cube. drawing calibration and distance between sphere and cube. playing also with holes. S.B
Licence: Personal use only
Creality CloudFree
I designed this all-in-one calibration cube so that I can run various tests in only one small print, without wasting that much filament.
Licence: Personal use only
Creality CloudFree
Outer dimensions are 50x50x50mm and the inner dimensions of the cube are 30x30mm. Outer dimensions are 25x25x25mm and the inner dimensions of the cube are 15x15mm.
Licence: Attribution
Creality CloudPaid
Use these models to see how aligned your multicolour printing is. Size: 20x20 mm Print From any material. Tested with Creality K1, Ender 3 Pro, A1 Mini
Licence: Marketplace terms
Creality CloudFree
Cali-Cube! Is your printer truly capable of producing high-quality prints? When you're checking precision, consistency, and overall performance, a simple geometric model like this cube is one of the best tools you can use.
Licence: Personal use only
Creality CloudFree
This cube is designed for a Delta or Kossel Printers. Why another test cube??? Well, because a delta or kossel printer if not assembled properly can print perfectly except the printed part can come out a mirror image of the intended...
Licence: Attribution
Creality CloudFree
A simple calibration cube to help dial in your settings for your printer.
Licence: Personal use only
Creality CloudFree
Use this to test your printer's capability all in just one tiny cube!
Licence: Personal use only
Creality CloudFree
7 primitives with 4 different shapes and 2 different sizes. Boost Me If you want more printing test !
File types: STLLicence: Marketplace terms
MakerWorldFree
This is a 25x25x25 cube you can do anything with (make a dice etc…) and is free to sell!!! Boost Me you probably don't want to waste your tokens on me lol! But each boost is approx.
File types: STLLicence: Marketplace terms
MakerWorldFree
The Bad version of our beloved xyz cube, is this the best of the worst or the worst one ever? Try it and find out :)
File types: STLLicence: Marketplace terms
MakerWorldFree
A compact XYZ calibration cube designed to quickly check your 3D printer’s dimensional accuracy and overall print quality.
File types: STLLicence: Marketplace terms
MakerWorldFreeSliSearch lists public model details and links to the original source. It does not host files or verify licences.